R1,972.19
CODE: DH-FFM
Polycarbonate anti-fog and impact resistant visor
Peripheral optical vision of 220°
TPR (Thermo Plastic Rubber) 5-point adjustable head harness
Large face seal flange
High efficiency exhalation valve
Separate mask body
Standard Dromex unifit filters
Withstands a pull of 15kg
One size fits all
Designed to withstand temperatures of up to 70 ± 3°
COMPOSITION
Polycarbonate anti-mist visor
TPR 5-point adjustable head harness
SUITABLE FOR USE IN
Chemical
Asbestos
Painting
Law Enforcement
Sanding & Grinding
Search & Rescue
General Industrial
In stock (can be backordered)
Full Face Mask
The Dromex® DHFFM full face mask provides the user with unparalleled vision, comfort and reliability protecting against hazardous vapours, gases and particulates, provided there is sufficient oxygen present in the contaminated atmosphere.The Dromex® full face mask utilizes the Dromex® twin uni-fit cartridges and pre-filters only.
| Weight | 2.25 kg |
|---|---|
| Dimensions | 30 × 20 × 15 cm |
| Special Instructions | All respiratory selections should be read in conjunction with BS EN 529:2005 “Respiratory Protective devices – Recommendations for selection, use, care and maintenance”. Do not use these respirators or enter in area where: • The oxygen concentration is not known or is less than 19.5%. • Contaminants or their concentrations are unknown or are known to be immediately dangerous to life or health. • Particulate concentrations exceed levels fixed by the applicable health and safety regulations or protection factor 40 NPF whichever is lower. • Gases and/or vapours are present except for respirators designated as protecting against vapours, in which case vapour concentrations should not exceed 20 NPF. • The requirement for leak tightness is unlikely to be achieved if worn against a beard or facial stubble. • Do not wear standard eye glasses with a full-face respirator • Not to be used for firefighting. • These respirators do not supply oxygen. Do NOT use in oxygen deficient atmospheres (e.g. tanks or other poorly ventilated areas). • Do not use in explosive atmospheres. • Do not modify or alter this device. |
| Compliance & Conformity | NRCS Homologated to SANS 50136:1998 CL1 as required by the Occupational Health and Safety Act, 1993 (Act No. 85 of 1993). EN136:2008 approved: Respiratory protective devices full face masks — Requirements, testing, marking quality system as per ISO9001:2008 |
| Specifications | Type: Class1 full face masks for light duty use Material: Thermo Plastic Elastomer/Rubber Colour: Black Harness: 5-point comfort harness with 2 grip holes for easier fitting on and removing with gloves and accommodation of women’s hair (ability to wear a pony tail). Withstands a pull of up to 15KG or 150N Visor: Polycarbonate anti-fog and impact resistant with peripheral optical vision of 220 degree’s (110 on the left and right). The natural field of vision is greater than the 70% specified of EN136:2008 standards. One size mask body: Accommodates small to large facial size's Temperature: Designed to withstand temperatures of up to 70 ± 3˚ Light weight dual filter cartridge system evenly distributes weight of mask and cartridges on the face. |
| Cleaning & Maintenance | – Remove cartridge filters from connectors and all inhalation and exhalations valves. – Clean / disinfect the face piece and components with a damp cloth, using lukewarm with all-purpose detergent (neutral, pH 6-8, e.g.: washing-up liquid), warm soapy water or cleaning solution not exceeding 30 degrees. – Do not immerse the product in water or use abrasive cleaners. – Do not use solvents (e.g alcohol, acetone, turpentine), hot water, strong detergents, bleaches or petroleum based products to clean any part of masks. – Dry in air at room temperature. – Replace all components after cleaning and inspect for visible damage. |
| Shelf life | 5 years, with correct maintenance and storage procedures. Discardimmediately if mask is damaged and tears are visible. |
| Materials | None of the materials used in the manufacture are known to adversely affect the hygiene or health. |
| Disposal | All industrial waste should be disposed of correctly according to local regulations and good disposal practice. Respiratory protective devices should be disposed of considering the hazardous substance they were used for. Please consider recycling. |
